P0111 — Your intake air temperature sensor is giving bad readings: causes, fixes & cost | TroubleAtlas

🌐 ▾
The TroubleAtlas app on a phoneTROUBLEATLAS APP · FREEFREE APPDownload our free appDownload our free appOur shopping centre in your pocket: dozens of suppliers that deliver in your country, compared, department by department.Dozens of suppliers compared, in your country. Get it free Get it free
OBD-II · FAULT CODE
P0111.

Your intake air temperature sensor is giving bad readings or not reading at all

P0111 — P0111 means your intake air temperature sensor is giving bad readings or not reading at all. Left unaddressed, this may cause your engine to run too rich or . It is a low-severity fault: you can usually keep driving for short distances. The most common cause is defective or failed iat sensor — signal voltage static (no temperature variation) or resistance outside 10–50 kω range at 20°c,loose, corroded, or damaged iat sensor connector — corrosion or oxidation causes intermittent signal loss. Typical fix: clean any corroded sensor terminals (contact cleaner and a fine brush or “terminal file”),securely reseat connectors to ensure reliable connection,return intake to oem configuration if aftermarket modifications are interfering,repair pcm/ecu wiring or.

CAN YOU STILL DRIVE? NO — REPAIR FIRST

"The automotive equivalent of a paper cut. Fix it when you're not busy."

Car dashboard with warning lights on
SEVERITY
LOW — NO — REPAIR FIRST
OBD2 SCANNER
TROUBLEATLAS APP
01What it means & symptoms

P0111 is a powertrain diagnostic trouble code. It identifies a fault related to The P0111 occurs when the PCM reads a signal in the IAT circuit which varies from expected values based on other sensor readings (such as the Engine Coolant Temperature sensor). This is a distinct condition from related codes P0112 and P0113. For these codes the PCM reads either a consistent high or low voltage in the IAT circuit. The powertrain control module monitors this circuit or component continuously and sets P0111 when the signal or value is outside the expected range, implausible or missing. This can affect engine performance, fuel economy or emissions and usually turns on the check-engine light. The base function may still work, but performance can be affected, so the fault should be diagnosed. Diagnosis generally means inspecting the related wiring, connectors and power/ground references, then verifying the component against specification with a scan tool.

  • Check Engine light (MIL) illuminated — verify with: OBD2 scanner (read freeze frame data),Difficulty starting in cold conditions — verify with: test start below 5°C, note cranking time,Elevated fuel consumption — verify with: fuel economy gauge or fill-to-fill calculation over 200 km,Rough idle and unstable RPM at low load — verify with: OBD2 scanner live data (idle RPM variance >200 RPM indicates IAT error),Reduced engine power under acceleration — verify with: test drive, note lag in response vs. expected baseline
02Most likely causes
Ranked from field data — confirmed by ≥2 independent sources.
#Cause
01Defective or failed IAT sensor — Signal voltage static (no temperature variation) or resistance outside 10–50 kΩ range at 20°C,Loose, corroded, or damaged IAT sensor connector — Corrosion or oxidation causes intermittent signal loss
02inspect intake manifold connector area,Interrupted or shorted IAT circuit wiring — Typically caused by heat damage near exhaust manifold or abrasion in harness routing,ECM malfunction in processing IAT signal — Rare
03confirm after sensor and wiring tests pass
05How to fix it
The repair path once the cause is confirmed.
01
Clean any corroded sensor terminals (contact cleaner and a fine brush or “terminal file”),Securely reseat connectors to ensure reliable connection,Return intake to OEM configuration if aftermarket modifications are interfering,Repair PCM/ECU wiring or
02
rarely
03
replace/control module if proven faulty after all other steps
09Repair cost
Indicative repair cost for P0111 — labour by country (parts excluded) plus a DIY/Pro estimate. Prices vary by area and workshop.

Typical operations: Mass Air Flow Sensor, O2 Sensor - Upstream, Diagnostic Scan · avg labour ≈ 0.7 h.

Workshop labour by countryHourly rateEst. labour
IT€45/h€29–€540
ES€55/h€36–€660
FR€75/h€49–€900
UK£80/h£52–£960
DE€95/h€62–€1140
US$120/h$78–$1440
Parts & totalDIYPro
P0111 means your intake air temperature sensor i€18–€55€58–€95

Our departments

Everything you need, picked by us

13Technical Service Bulletins & recalls

No technical service bulletins or recalls currently reference P0111. This section updates automatically when manufacturers publish related bulletins.

12Which vehicles get this code
14Frequently asked questions
Which vehicles most commonly report P0111?

In our database P0111 is recorded across 495 vehicle models — most frequently on the Hyundai Santa-Fe, Hyundai Tucson, Ford F-150.

What do real owners report when they get P0111?

A Volkswagen Golf owner reported to NHTSA: “Since shortly after purchase, the vehicle has experienced intermittent drivability and shifting issues along with repeated EPC and check engine warnings. Diagnostic trouble code P0111 (intake air temperature plausibility) has been present…”

Can I keep driving with P0111?

NO — REPAIR FIRST.

How much does it really cost to fix P0111?

Typically €18–€55 as a DIY repair and €58–€95 at a workshop — the final figure depends on the actual cause and your vehicle.

Scroll to Top